<?xml version="1.0"?>
<?xml-stylesheet type="text/xsl" href="Manuals.xslt"?>
<!--edited 3 9 2015 SCH-->

<manual>
  <header>
    <text>K-2840</text>
    <text>REAR, W/AIRMATIC
WARRANTY COIL SENSOR REPLACEMENT</text>
    <text>FOR MERCEDES-BENZ S-CLASS (W220)</text>    
  </header>
  
  <section>
	<photo>
    	<image file="..//K-2840/K-2840_001.jpg" alt="K-2840 Rear, w/Airmatic Warranty Coil Sensor Replacement" title="K-2840 Rear, w/Airmatic Warranty Coil Sensor Replacement" />
	</photo>
  </section>
  
    <section>
    <warning>
      <image file="..//ManualImages/warning_symbol.png"  alt="Warning" title="Warning"/>
      <text>
        The air suspension system is under pressure (up to 10 bar, or 150 lbf/in). Verify pressure has been relieved and disconnect power to the air suspension system prior to disassembly. Do not allow dirt or grease to enter the system. Always wear standard hand, ear, and eye protection when servicing the air suspension system. 
      </text>
    </warning>
  </section>
  
    <section>
    <disclaimer>
   		Arnott® is committed to the quality of its products. If you have a question or problem with any Arnott product, please contact Arnott by calling 800-251-8993 during normal business hours or email
    </disclaimer>
  </section>
  
  <section>
    <headline_large_left>GENERAL INFORMATION:</headline_large_left>
 </section>
 
  <section>
    <disclaimer>
      Reading this manual signifies your agreement to the terms of the general release, waiver of liability, and hold harmless agreement, the full text of which is available at
    </disclaimer>
  </section>
  
    <section>
    <list_item>Not to be stored below 5&#176;F (-15&#176;C) or above 122&#176;F (50&#176;C).</list_item>
    <list_item>Avoid damage to air lines and cables.</list_item>
    <list_item>Removal and installation is only to be performed by fully qualified personnel.</list_item>
    <list_item>Use car manufacturer’s diagnostic software.</list_item>
  </section>
  
  <section>
    <caution>
      Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified
in the instructions or in a different sequence.
    </caution>
  </section>
  
  <section>
    <warning>
      <image file="..//ManualImages/warning_symbol.png"  alt="Warning" title="Warning"/>
      <text>
         To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to
disconnect your battery.
      </text>
    </warning>
  </section>
  
  <section>
    <warning>
      <image file="..//ManualImages/warning_symbol.png"  alt="Warning" title="Warning"/>
      <text>
         Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for
additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath
the vehicle if it is not adequately supported, as serious injuries and death can occur.
      </text>
    </warning>
  </section>
  
  <section>
    <headline_large_left>COIL SENSOR REMOVAL</headline_large_left>
 </section>
 
 <section>
 	<text>
 		1. Raise the vehicle and remove the wheel.
 	</text>
 </section>
 
 <section>
 	<text>
 		2. Follow the coil harness wire and remove from strain relief locations as required. Disconnect coil harness from vehicle. (FIGURES 1, 2)
 	</text>
 </section>
 
 <section>    
    <dbl_image file1="..//K-2840/K-2840_002.jpg" alt1="FIGURE 1" title1="FIGURE 1" caption1="FIGURE 1" file2="..//K-2840/K-2840_003.jpg" alt2="FIGURE 2" title2="FIGURE 2" caption2="FIGURE 2" />
  </section>
  
  <section>
 	<text>
 		3. Remove upper and lower caps and screws. (FIGURES 3, 4, 5)
 	</text>
 </section>
 
 <section>    
    <dbl_image file1="..//K-2840/K-2840_004.jpg" alt1="FIGURE 3" title1="FIGURE 3" caption1="FIGURE 3" file2="..//K-2840/K-2840_005.jpg" alt2="FIGURE 4" title2="FIGURE 4" caption2="FIGURE 4" />
  </section>
  
  <section>    
    <sngl_image file="..//K-2840/K-2840_006.jpg" caption="FIGURE 5" alt="FIGURE 5" title="FIGURE 5" />
  </section>
  
  <section>
 	<text>
 		4. Remove harness and rubber gaskets from coil. (FIGURES 6, 7, 8, 9)
 	</text>
 </section>
 
 <section>    
    <dbl_image file1="..//K-2840/K-2840_007.jpg" alt1="FIGURE 6" title1="FIGURE 6" caption1="FIGURE 6" file2="..//K-2840/K-2840_008.jpg" alt2="FIGURE 7" title2="FIGURE 7" caption2="FIGURE 7" />
  </section>
  
  <section>    
    <dbl_image file1="..//K-2840/K-2840_009.jpg" alt1="FIGURE 8" title1="FIGURE 8" caption1="FIGURE 8" file2="..//K-2840/K-2840_010.jpg" alt2="FIGURE 9" title2="FIGURE 9" caption2="FIGURE 9" />
  </section>
  
  <section>
    <headline_large_left>COIL SENSOR INSTALLATION</headline_large_left>
 </section>
 
 <section>
 	<text>
 		1. Installation is in reverse order of coil sensor removal using the hardware supplied in this kit.
 	</text>
 </section>
 
 <footer>
  	<partNumber>K-2840</partNumber>
  	<revision>REV 3</revision>
  	<date>03/03/2016</date>
  </footer>
  
</manual>
