0
AS-3368
ARNOTT NEW FRONT EIBACH AIR STRUT
FOR 2014-2018 LAND ROVER RANGE ROVER SPORT (L494) W/VDS - LT/RT
The air suspension system is under pressure (up to 10 bar, or 150 lbf/in). Verify pressure has been relieved and disconnect power to the air suspension system prior to disassembly. Do not allow dirt or grease to enter the system. Always wear standard hand, ear, and eye protection when servicing the air suspension system.
Reading this manual signifies your agreement to the terms of the general release, waiver of liability, and hold harmless agreement, the full text of which is available at
Not to be stored below 5°F (-15°C) or above 122°F (50°C).
Avoid damage to air lines and cables.
Removal and installation is only to be performed by fully qualified personnel.
Use car manufacturer’s diagnostic software.
Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified
in the instructions or in a different sequence.
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to
disconnect your battery.
Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for
additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath
the vehicle if it is not adequately supported, as serious injuries and death can occur.
THE PRODUCT SHOWN IN THE INSTALLATION STEPS BELOW MAY LOOK DIFFERENT THAN THE PART YOU ARE INSTALLING. THE INSTALLATION STEPS ARE THE SAME AND ALL NOTICES AND WARNINGS SHOULD BE ADHERED TO IN THE SAME MANNER.
1. Set steering to straight ahead.
3. Remove the applicable front wheel. (FIGURE 1)
4. Disconnect the electrical connection from the top of the strut by pressing in on the two tabs and pulling upwards. (FIGURE 2)
5. Loosen and remove the air line from the top of the strut. (FIGURES 3, 4)
6. Remove the air line fitting. To do so, spread the collet open and the remaining fitting will slide off of the air hose. (FIGURES 5, 6, 7, 8)
7. Loosen and remove the top mounting nuts. (FIGURES 9, 10)
8. Loosen and remove the sensor wire and brake line bracket. (FIGURES 11, 12, 13)
9. Locate and remove the upper control arm ball joint nut. Separate the ball joint from the spindle assembly. (FIGURES 14, 15, 16)
10. Loosen and remove the lower strut mounting bolt. (FIGURE 17)
11. Remove the sensor wire bracket and separate the end link from the lower strut clevis. (FIGURES 18, 19, 20)
12. Loosen the strut clevis. (FIGURE 21)
13. Pull the spindle assembly outward and remove the strut. (FIGURES 22, 23)
Tighten all nuts and bolts to manufacturer's specifications during the installation process.
Do not remove the air fitting from the air strut. Doing so may cause damage and/or void warranty. Remove the white shipping pin from the new air fitting and insert the air line until fully seated.
1. Install the strut into the vehicle. (FIGURE 24)
2. Install the four (4) top strut mounting bolts and tighten to manufacturer's specifications. (FIGURE 25)
3. Install the lower strut mounting bolt. (FIGURE 26)
4. Reinstall the upper control arm to the spindle assembly and tighten to manufacturer's specifications. (FIGURES 27, 28)
5. Reinstall the sensor wire bracket and reattach the end link to the lower strut clevis. (FIGURES 29, 30, 31)
6. Retighten the strut clevis to manufacturer's specifications. (FIGURE 32)
7. Reinstall the sensor wire and brake line bracket. (FIGURES 33, 34)
8. Remove the white plastic shipping pin from the air line fitting and discard. (FIGURE 35)
9. Install the air line into the air line fitting. (FIGURES 36, 37)
10. Reinstall the electrical connection, ensuring the plug is oriented appropriately to the electrical terminals within the strut. (FIGURES 38, 39)
12. Inflate air system per manufacturer's specifications.
14. Installation complete.