Arnott Installation Manuals
C-2836
ARNOTT COIL SPRING CONVERSION KIT
FOR 2007-2014 VARIOUS LONG WHEELBASE GM SUVs

Congratulations on your purchase of an Arnott® air suspension product. We at Arnott Incorporated are proud to offer a high quality product at the industry’s most competitive pricing. Thank you for your confidence in us and our product.

Proper installation is essential to experience and appreciate the benefits of this system. Please take a moment to review these installation instructions before you begin to install these components on your vehicle. The removal and installation of air suspension products should only be performed by a fully qualified, ASE Certified, professional.

It is equally important to be aware of all necessary safety measures while installing your new Air Suspension System. This includes proper lifting and immobilizing of the vehicle and isolation of any stored energy to prevent personal injury or property damage.

"Engineered to Ride, Built to Last®"

C-2836 Arnott Coil Spring Conversion Kit

WARNING: The air suspension system is under pressure (up to 10 bar, or 150 lbf/in). Verify pressure has been relieved and disconnect power to the air suspension system prior to disassembly. Do not allow dirt or grease to enter the system. Always wear standard hand, ear, and eye protection when servicing the air suspension system.

Arnott Industries® is committed to the quality of its products. If you have a question or problem with any Arnott product, please contact us by calling +1 321-868-3016 during normal business hours or email techassistance@arnottinc.com (In the EU please call +31 (0)73 7850 580 or email Info@arnotteurope.com).

GENERAL INFORMATION:

Reading this manual signifies your agreement to the terms of the general release, waiver of liability, and hold harmless agreement, the full text of which is available at www.arnottinc.com

Not to be stored below 5°F (-15°C) or above 122°F (50°C).

Avoid damage to air lines and cables.

Removal and installation is only to be performed by fully qualified personnel.

Use car manufacturer’s diagnostic software.

CAUTION: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.

WARNING: To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.

WARNING: Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.

COIL STRUT REMOVAL

1. Raise vehicle and remove front wheels to expose the front coil struts. (FIGURES 1, 2)

FIGURE 1
FIGURE 1
FIGURE 2
FIGURE 2

2. Lift the hood to expose the top of the coil struts. Locate and disconnect the electrical connectors. Secure the harness in a way not to interfere with any moving parts or components with excessive heat. (FIGURES 3, 4)

FIGURE 3
FIGURE 3
FIGURE 4
FIGURE 4

3. Remove the wire clips and top mounting nuts. (FIGURES 5, 6, 7)

FIGURE 5
FIGURE 5
FIGURE 6
FIGURE 6

FIGURE 7
FIGURE 7

4. Remove the lower mounting bolts. (FIGURES 8, 9)

FIGURE 8
FIGURE 8
FIGURE 9
FIGURE 9

5. Loosen, do not remove, the sway bar end link hardware. (FIGURE 10)

FIGURE 10
FIGURE 10

6. Carefully remove coil struts from the vehicle. (FIGURE 11)

FIGURE 11
FIGURE 11

WARNING: Use a spring compressor tool for the following removal steps.


COIL STRUT DISASSEMBLY

1. Release clip and remove the top electrical connector and shock rod stem. (FIGURES 12, 13, 14 ,15)

FIGURE 12
FIGURE 12
FIGURE 13
FIGURE 13

FIGURE 14
FIGURE 14
FIGURE 15
FIGURE 15

2. Compress the coil spring and remove the top shock rod nut. (FIGURES 16, 17)

FIGURE 16
FIGURE 16
FIGURE 17
FIGURE 17

3. Remove top mount plate, offset plate and rubber isolator. (FIGURES 18, 19)

FIGURE 18
FIGURE 18
FIGURE 19
FIGURE 19

4. Carefully release spring pressure and remove the coil spring, spacer washer, bump stop, bump stop cap, and spring seat. (FIGURES 20, 21, 22)

FIGURE 20
FIGURE 20

FIGURE 21
FIGURE 21
FIGURE 22
FIGURE 22

COIL STRUT REASSEMBLY

WARNING: Tighten all nuts and bolts to manufacturer's specifications during the installation process.

1. Install the OEM spring seat, making sure the flanged end of the spring seat is down, followed by the bump stop cap onto the new shock absorber. (FIGURE 23)

FIGURE 23
FIGURE 23

2. Properly align the strut before installing it on the vehicle, making sure the bolt mounts are facing downward as shown below. (FIGURES 24, 25)

FIGURE 24
FIGURE 24
FIGURE 25
FIGURE 25

3. Remaining assembly is in the reverse order of shock removal.

COIL STRUT INSTALLATION

WARNING: Tighten all nuts and bolts to manufacturer's specifications during the installation process.

1. Installation is in reverse order of shock removal.

2. Position the T-bar on top of the control arm to ensure proper mounting. (FIGURE 26)

FIGURE 26
FIGURE 26

REAR AIR SHOCK/COIL SPRING REMOVAL

1. Set steering to straight.

2. Raise vehicle.

3. Remove the rear wheels. (FIGURE 27)

FIGURE 27
FIGURE 27

4. Locate and remove the air lines to deflate the air shocks. Turn the metal clip approximately 90° to remove the air line fitting from the air shock. (FIGURE 28)

FIGURE 28
FIGURE 28

5. Locate and remove the electrical connectors from the top of the air shocks. (FIGURE 29)

FIGURE 29
FIGURE 29

6. Loosen and remove the upper and lower shock mounting nuts. (FIGURES 30, 31)

FIGURE 30
FIGURE 30
FIGURE 31
FIGURE 31

7. Support the axle to relieve pressure from the air shocks mounting points. Remove the upper and lower air shock mounting bolts. (FIGURE 32)

FIGURE 32
FIGURE 32

8. Remove the air shocks from the vehicle. (FIGURE 33)

FIGURE 33
FIGURE 33

9. Remove the bolts and ride height sensors from the upper control arms. (FIGURES 34, 35)

FIGURE 34
FIGURE 34
FIGURE 35
FIGURE 35

10. Remove the bolt and bracket holding the brake line to the rear differential. (FIGURES 36, 37)

FIGURE 36
FIGURE 36
FIGURE 37
FIGURE 37

11. Remove the nuts on the upper sway bar end links. (FIGURE 38)

FIGURE 38
FIGURE 38

12. Using a jack or other suitable device, support the axle to release pressure from the sway bar end links. Remove the sway bar end link bolts. (FIGURES 39, 40)

FIGURE 39
FIGURE 39
FIGURE 40
FIGURE 40

13. Slowly lower the axle and remove the coil springs. (FIGURE 41)

FIGURE 41
FIGURE 41

REAR COIL SPRING INSTALLATION

WARNING: Tighten all nuts and bolts to manufacturer's specifications during the installation process.

1. Install the rear coil conversion in the reverse order of removal.

NOTE:  Secure the air lines and electrical connectors in suitable locations as they are not used for this kit.

ELECTRONIC BYPASS MODULE INSTALLATION

1. Remove side fuse box cover. (FIGURE 42)

FIGURE 42
FIGURE 42

2. Remove lower dash hardware and remove lower dash cover. (FIGURES 43, 44, 45, 46, 47)

FIGURE 43
FIGURE 43
FIGURE 44
FIGURE 44

FIGURE 45
FIGURE 45
FIGURE 46
FIGURE 46

FIGURE 47
FIGURE 47

3. Remove OBD mounting screw and drop the plug down. (FIGURES 48, 49)

FIGURE 48
FIGURE 48
FIGURE 49
FIGURE 49

4. Remove air conditioning duct. (FIGURE 50)

FIGURE 50
FIGURE 50

5. Trim back the plug harness sheath. (FIGURE 51)

FIGURE 51
FIGURE 51

6. Using the wiring diagram, match up the wires and splice them together with the t-tap connectors. (FIGURES 52, 53, 54, 55, 56, 57, 58)

ELECTRONIC BYPASS MODULE FROM PIN# (WIRE/COLOR) VEHICLE’S WIRING HARNESS
BLUE 6 (TAN/BLACK)
RED 16 (RED/WHITE)
GREEN 14 (TAN)
BLACK 4 (BLACK)

FIGURE 52
FIGURE 52
FIGURE 53
FIGURE 53

FIGURE 54
FIGURE 54

FIGURE 55
FIGURE 55
FIGURE 56
FIGURE 56

FIGURE 57
FIGURE 57
FIGURE 58
FIGURE 58

7. Once all the wires have been connected you will need to secure the EBM under the dash and away from any source of heat and/or any moving parts. (FIGURE 59)

FIGURE 59
FIGURE 59

8. Reassemble the dash by reinstalling the air conditioning duct, lower dash cover, lower dash hardware, and side fuse box cover.

9. EBM installation complete.

10. Remove the cover from the fuse box in the engine compartment. (FIGURE 60)

FIGURE 60
FIGURE 60

11. Remove the 30-amp fuse in Location #2 labeled as "ESC/ALC EXH". (FIGURES 61, 62)

FIGURE 61
FIGURE 61
FIGURE 62
FIGURE 62


NOTE:  If the fuse is not removed a warning light will be displayed in the instrument cluster.

12. Reinstall the fuse box cover.

13. Installation complete.

C-2836 REV 7 03/08/2018